User Tag List

Page 3 of 3 FirstFirst 123
Results 51 to 68 of 68

Thread: TTB MJ

  1. #51
    Wheeler
    Join Date
    15 Dec 2005
    Location
    Golden Valley
    Age
    47
    Posts
    403
    Real Name
    Jack
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Are the bent tie rods for frame clearance on compression? Do they need that much bend? I like it, just curious as from even a desert bashing standpoint it seems as if those are at risk.

    Jack
    1985 4Runner in the making, 2006 LJ Rubicon-Sold
    2007 Chevy 2500hd max/ali, 2008 FWC Pop-Up Camper

  2. #52
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Quote Originally Posted by locrwln View Post
    Are the bent tie rods for frame clearance on compression? Do they need that much bend? I like it, just curious as from even a desert bashing standpoint it seems as if those are at risk.

    Jack
    Yeah, they are bent for clearance at full bump. Drivers has to clear the pitman arm and passengers has to clear the swingset. It's all 1.5" .250 wall Dom so it should be plenty stout. Pretty common practice on these TTBs.

  3. #53
    Wheeler
    Join Date
    15 Dec 2005
    Location
    Golden Valley
    Age
    47
    Posts
    403
    Real Name
    Jack
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by Toymerica View Post
    Yeah, they are bent for clearance at full bump. Drivers has to clear the pitman arm and passengers has to clear the swingset. It's all 1.5" .250 wall Dom so it should be plenty stout. Pretty common practice on these TTBs.
    Gotcha. Sometimes, you gotta do what you gotta do.

    Jack
    1985 4Runner in the making, 2006 LJ Rubicon-Sold
    2007 Chevy 2500hd max/ali, 2008 FWC Pop-Up Camper

  4. The Following User Likes locrwln's Post:

    Toymerica (February 11th, 2016)

  5. #54
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)


    Was cleaning some stuff up and came across a few of the many CAD(cardboard aided design) artifacts I had from the beam work.

    On a side note if someone needs a template for front Frame stiffeners I have one. All you gotta do is trace it, plasma it and weld it.

  6. The Following User Likes Toymerica's Post:

    turbobrick (February 11th, 2016)

  7. #55
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Nothing to see here just a couple of jeep Couchmanches

  8. The Following User Likes Toymerica's Post:

    turbobrick (February 17th, 2016)

  9. #56
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Picked up some F.O.A 2.5" series dual bypasses. 18" travel. Valved heavy for compression and light for rebound. Adjustable rebound valving, as well as dual adjustable compression valving. Should pair well with the Deaver springs in the rear.


  10. The Following 6 Users Like Toymerica's Post:

    Deluxxx (March 12th, 2016), ford boy (March 12th, 2016), gird123 (March 12th, 2016), Mattbarnes16 (March 14th, 2016), mattific (March 13th, 2016), turbobrick (March 12th, 2016)

  11. #57
    Web Wheeler
    Join Date
    29 Jan 2013
    Location
    reno
    Age
    27
    Posts
    931
    Real Name
    Mark
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    so how much travel is this thing pulling?

  12. #58
    I support Reno4x4!
    Join Date
    31 Mar 2005
    Location
    Edge City, NV
    Posts
    10,084
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)
    LOL i pull you out of the icy peavine ditch and you get rig of the month- pic taken same day. get the front to work yet?
    Great spirits have always encountered violent opposition from mediocre minds.

    Albert Einstein


    <a href=http://i2.photobucket.com/albums/y12/RARECJ8/rareCJ8.jpg target=_blank>http://i2.photobucket.com/albums/y12...J8/rareCJ8.jpg</a>
    www.hillsangels4x4.com. Plankowner
    Life Member Blue Ribbon Coalition
    Cal 4 Wheel
    ECV #3691


    Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt ut labore et dolore

  13. The Following User Likes RARECJ8's Post:

    MARKUNIT10 (May 6th, 2016)

  14. #59
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Quote Originally Posted by RARECJ8 View Post
    LOL i pull you out of the icy peavine ditch and you get rig of the month- pic taken same day. get the front to work yet?
    Hahaha funny the way that worked out.

    I'll be getting the 4x4 trans, transfer case and rear end done this fall so she if all goes well she should be 4x4 and fully operational this winter

  15. #60
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Finally getting work done on the back half of the Comanche. Life happens so there was a 2 year gap between the front and rear. But stay tuned



    In her temporary home, tore out the factory Dana 44, gas tank and 2 wheel drive aw4 transmission


  16. #61
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)

    TTB MJ

    Decided to stick with the aw4 auto, and doing an NP203/Dana 300 dual transfer cases setup:

    Here's the factory tail housing before



    After: swapped a dodge np203 23 spline input into my GM203 case, has damn near full spline engagement, seal retainers bottom out on each other and the transmission side seal does not sit on the shorter 203 input so I cut it out. GM relies on just the np203 seal(a dual sided seal) to keep atf separate from the gear oil so it should be just fine



    Gap before hacking up the tailhousing seal retainer



    Grease line Where the trans seal was (no seal)



    Sits nice and flush, just gotta disassemble the 203, and re-drill and tap it for the aw4 circle pattern



    Settled where I want it, and transfer punched where to drill nice part is the tail housing was a tight/perfect fit over the input bearing retainer so it's self centering



    Original holes plugged with flush Allen bolts and rtv

    New holes tapped and ready for assembly




  17. #62
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)

    TTB MJ

    Aw4 to np203 is a success






    All mated up:


  18. #63
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Now onto getting the flipped Dana 300 prepped



    She was in great shape, so I'm just gonna run it!



    Pulled the now top plate added a breather and a sight tube so I can easily check oil level



    Adavance adapter np203/300 adapter plate re-sealed and back on


  19. #64
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)

    TTB MJ

    Getting all my Ruff Stuff brackets welded

    Adjustable upper link mounts





    Pinion guard


    Axle side horizontal upper link mounts

    Tacked in place on the 9"


    Offset chassis link mount brackets for mounting my trailing arms just outside of the frame


  20. #65
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Swapping a 1998+ aw4 trans so I used a 1989-1997 tailhousing and just swapped it into the 1998+ trans along with the output speed sensor and rotor, just gotta swap some connectors, solder some wires and it will all be plug and play.

    Short fat sensor is the newer style 4 pulse style

    Long skinny is the older single pulse style that my jeep is setup for electronically



    Removed the black 4 pulse rotor and swapped over a single pulse rotor (jeep has two snap ring slots like they knew us old jeepers would switch to the newer trans)



    Forced the jeep to accept the gm203 range box


  21. The Following 3 Users Like Toymerica's Post:

    Reckless Aaron (1 Week Ago), Sierra Valley (1 Week Ago), turbobrick (1 Week Ago)

  22. #66
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Welding for hours on the ruffstuff 48" URC trailing arms




    Got the 9" more or less in place at ride height so I can get some mounts mocked up



    Also made some frame stiffeners to plate the outside of the frame under the cab to reinforce where the trailing arm outriggers will mount



    All welded in place




  23. #67
    Wheeler
    Join Date
    16 Nov 2007
    Location
    Sparks, Nv
    Age
    31
    Posts
    205
    Real Name
    Chris
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    What happen to the deavers? Did you ever have them? I love the linked rear over the deavers though.
    Quote Originally Posted by BIG BLUE View Post
    Thats hysterical....whoa and I thought I was the master of booty fab. I feel like such an amateur. Its not even even...no way that can be real.

  24. #68
    Wheeler
    Join Date
    08 Nov 2013
    Location
    Reno
    Age
    23
    Posts
    72
    Real Name
    Eric
    Mentioned
    0 Post(s)
    Tagged
    1 Thread(s)
    Quote Originally Posted by chrisdaledevine View Post
    What happen to the deavers? Did you ever have them? I love the linked rear over the deavers though.
    I had deavers and bypasses. Sold them both when I decided to ball out and link it.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •